Network problems on your Meyton shooting range may have different symptoms. Typical Symptoms are:
- Control-PCs lose the connection to the Electronic Scoring Target. ESTA5 loses the connection to the Electronic Scoring Target. ESTA-Pro and ESTA-Control show a blue view and try connecting to the Electronic Scoring Target.
- A lane is shown in the ShootmasterII software. The lane cannot be freed. The lane cannot be occupied.
- A lane is not showing in the ShootmasterII software.
- A lane does not accept disciplines.
- A shooter is attributed to a lane via the ShootmasterII software. The lane does not accept the shooter. ESTA5 does not show the name of the shooter.
- A lane cannot be switched to match mode
Verify the following points.
Test your shooting range extensively after each point.
Re-establish the changes for each point before testing the next point. Repeat the changes of the preceding point.
Maintain a list of the changes. You can reset your shooting range after the troubleshooting.
Does the error disappear after switching off and on the devices?
Check if switching off and on the devices rectifies the error.
Perform the following actions:
- Switch off all devices, then switch on all devices again
- Switch off all devices, then switch on all devices again in a different order
- Switch off all devices, then switch on all devices again while waiting 1 Minute between devices
- Switch off all devices, then switch on all devices again in a different order while waiting 1 Minute between devices
YES: the error disappears after switching off and on the devices
Wait if the error appears again.
NO: the error does not disappear after switching off and on the devices
Continue troubleshooting.
Was the Workstation started before all other devices?
Background: For a flawless operation of the Meyton system several services run on the workstation. At the start of the system the connected devices request the standby of the services. If the connected devices do not get an answer on their request of the services, the devices report errors.
NO: the Workstation was started at the same time as or even after all other devices were started.
- Shutdown the whole system.
- Start the Workstation. Log in. Start the Meyton ShootMasterII Software. Wait 1 minute.
- Start the connected devices.
Continue troubleshooting.
Is the device active for more than one day?
Background: The longer a computer is active the more errors accumulate. When these errors accumulate they may create unclear symptoms. Tablets switch to sleep mode when pushing the power-on button.
YES: the device is active for more than one day
Switch off the device entirely. Restart the device.
If the device has an external power supply disconnect the power supply when the device is switched off. Wait 30 seconds. Reconnect the power supply. Restart the device.
If the device has an detachable battery detach the battery when the device is switched off. Wait 30 seconds. Reattach the battery. Restart the device.
If a short push on the power-off button of the tablet only put the device in sleep mode, keep the power-off button pushed until the device is switched off completely. Use the documentation of the manufacturer. Wait 30 seconds. Restart the device.
NO: the device is active for less than one day
Continue troubleshooting.
Are energy-saving options active on the device?
Background: Energy-saving options influence computing power and the network connectivity.
YES: There are energy-saving options active on the device
Use the documentation of the manufacturer of the device to ensure:
- the screen of the device is always on
- the network connection is always on
- Sleep mode: never
- WiFi in sleep mode: always active
- WiFi-optimisation: deactivated
- Standby and sleep mode during charging: deactivated (this setting requires the activation of developer mode. Use the documentation of the manufacturer of the device.)
Continue troubleshooting.
Are there energy-saving options active on the network devices?
Background: Energy-saving options influence computing power and the network connectivity.
YES: There are energy-saving options active on the device
Use the documentation of the manufacturer of the device to ensure:
- the routers in the network are always on
- the switches in the network are always on
- the Access Points in the network are sending WiFi signals continuously
Continue troubleshooting.
Are there switching loops in the network?
Verify:
- Do cables form a loop?
- Does a WiFi-connection form a loop?
- Is there a network-bridge active in a device?
- Are there parallel connections that have their end-points in common?
Remove the switching loops.
NO: There are no switching loops in the network
Continue troubleshooting.
Are all cables in the network undamaged?
Background: Damaged cables may affect the functionality of the network.
Check all cables of the network for
- Visible damage
- Kinks
- loose sockets
- corrosion
Replace the damaged cables.
YES: All network cables are undamaged
Continue troubleshooting.
Are all devices on the network undamaged?
Background: damaged device may affect the functionality of the network
Check all devices in the network for
- visible damage
- loose sockets
- corrosion
- water damage
- dust
- clogged fans
- obstruction of heat dissipation
Replace the damaged devices.
YES: All devices in the network are undamaged
Continue troubleshooting.
Are all devices on the network undamaged?
Background: damaged device may affect the functionality of the network
Check all devices in the network for
- visible damage
- loose sockets
- corrosion
- water damage
- dust
- clogged fans
- obstruction of heat dissipation[/i]
NO: Devices in the network are damaged
Replace the damaged devices.
YES: All devices in the network are undamaged
Continue troubleshooting.
Are there PowerLan-connections, network connections via electric cabling, WiFi Bridges or a wireless connection?
Background: Low signal quality may lead to random interruptions of the network connection. Devices of some manufacturers may disturb the network connection.
YES: there are PowerLan-connections, network connections via electric cabling, WiFi Bridges or a wireless connection in the network
Replace the connections with Ethernet cables.
NO: only Ethernet cables are in the network
Continue troubleshooting.
Are there managed switches or switches with security options in the network?
Background: Managed switches filter information depending on security options. These security options are also called firewalls. This filtering may influence the Meyton network. Managed switches are marked as such. Only non-managed switches forward information without filtering.
YES: there are managed switches or switches with security options in the network
Deactivate all security options and filters of managed switches. Use the documentation of the manufacturer.
Replace managed switches with non-managed switches.
NO: there are only non-managed switches in the network
Continue troubleshooting.
Is there more than one router in the network?
Background: A Router is a device that organises the network. Several routers in the network may lead to errors in the network.
YES: There are more than one router in the network
Make sure that there is only one router in the network.
Use the documentation of the manufacturer.
NO: there is only one router in the network
Continue troubleshooting.
Is there more than one DHCP-Server in the network?
Background: A DHCP-Server that distributes static and dynamic IP-addresses and subnetmasks in the network. A DHCP-server runs on a router or on a Access Point. A DHCP-server usually has a graphical interface. A user or an administrator configure the DHCP-Server.
YES: There are more than one DHCP-Server in the network?
Make sure that
- there is only one DHCP-server in the network
NO: There is only one DHCP-Server in the network
Make sure that
- the DHCP-Server does not attribute IP-addresses that are already used by Electronic Scoring Targets
- the DHCP-Server does not attribute IP-addresses that are already used by printers
- the DHCP-Server does not attribute IP-addresses that are already used by a workstation
- the DHCP-Server does not attribute the same IP-address twice
Use the documentation of the manufacturer.
Continue troubleshooting.
Has the whole network the same data transfer rate?
Background: There are different standards for the data transfer rate in a network. Common standards for the data transfer rate are:
- 100-Mbit/s (IEEE 802.3u)
- 1000-Mbit/s (Gigabit)
Meyton recommends for shooting ranges up to 50 systems the standard of 100-Mbit/s for the data transfer rate.
NO: The network is not on the same standard for the data transfer rate
Set the network on the same standard for the data transfer rate.
- Set the switches on the standard of 100-Mbit/s for the data transfer rate. Use the manufactures documentation.
- Change the cables, if they don't support the standard of 100-Mbit/s for the data transfer rate.
- Change the devices, if they don't support the standard of 100-Mbit/s for the data transfer rate.
Continue troubleshooting.
Are the versions of the software on the devices in the network up-to-date?
Make sure that the software on all devices in the network is up-to-date. Use the documentation of the manufacturer. Make sure that
- the router
- the DHCP-server
- the switches
- and all other devices in the network
NO: the versions of the software on the devices in the network are not up-to-date.
Update the software on the devices. Use the documentation of the manufacturer.
YES: the versions of the software on the devices in the network are not up-to-date
Continue troubleshooting.
Are the versions of the software on the Meyton devices on your shooting range up-to-date?
Make sure all Meyton devices have the most up-to-date version. Use the manual „Welche Version habe ich“ from the Meyton homepage.
NO: the versions of the software on the Meyton devices are not up-to-date
Execute an update. Use your customer login.
YES: the versions of the software on the Meyton devices are up-to-date
Continue troubleshooting.
Does the error follow the device during a cross-over test?
Background: A cross-over test confirms the device with the error. During the crossover test the device with the suspected error is replaced by a functioning device.
Find a shooting lane that functions properly. Replace the device with the suspected error with the same device from the functioning shooting lane.
Applicability
- Electronic Scoring Target. Test the Electronic Scoring Target on another shooting lane.
- Control-PCs. Test the Control-PC on another shooting lane.
- Display Controller. Test the Display Controller with another network socket.
- Control Panel. Test the Control-Panel with another Control-PC.
- Target illumination. Test the target illumination with another EST
YES: error persists after the cross-over test.
The error is on the device. Continue troubleshooting for that specific device.
NO: the error disappears after the cross-over test.
The error is in another device or in the network. Continue troubleshooting.
Is the socket of the Electronic Scoring Target undamaged?
Background: The socket of the Electronic Scoring Target connects it with power supply and with network. If the socket is damaged the Electronic Scoring Target will not connect with the network.
Disconnect the Electronic Scoring Target from the power supply.
Verify
- the socket is not loose
- both screws are firmly fixed
- the socket is clean and dry
- the rubber-joint is fixed in place
- bright and not corroded
- straight and not bent
- firmly fixed
NO: the socket of the Electronic Scoring Target is damaged
Contact Meyton.
YES: the socket of the Electronic Scoring Target is undamaged
Continue troubleshooting.
Was there an over-voltage on your shooting range?
Background: over-voltage damages electronics. The following events may induce an over-voltage:
- lightning
- disturbances of the power supply
- sudden losses of power supply
- electrostatic discharge
YES: there was an over-voltage on your shooting range
Verify all devices. Contact Meyton.
NO: there was no over-voltage
Continue troubleshooting.
Was there water damage on your shooting range?
Background: Water may damage electronics. The following events may lead to water damage
- condensation on a cold device while switching from a cold to a warm environment quickly
- storage of the device in a cold and/or damp environment without power supply
- rain
- splash water
- spilled drinks or food
YES: There is water damage
Verify the devices. Contact Meyton.
NO: there was no water damage
Continue troubleshooting.
Contact Meyton
Before contacting Meyton:
- Verify all the points in this troubleshooting!
- Note the serial number of the affected EST. You find the serial number on the EST. The serial number is on a small adhesive label near the socket of the EST.
- Note the versions of the software on the Meyton devices. Use the manual „Welche Version habe ich“ from the Meyton homepage.
- Note a precise error description! What happens? Under which conditions does it happen? When does it happen?
- Prepare your customer ID! You find your customer ID on all bills and offers from Meyton.
Use one of the following ways to contact Meyton:
- Use the contact information on http://support.meyton.info
- Write in the forum http://forum.meyton.info